Fisher & Paykel SmartDrive Washer Repair — Direct-drive SmartDrive washer specialists — faster diagnosis, fewer return visits.

Fisher & Paykel’s SmartDrive washers use a direct-drive motor system — no belts, no gearbox — which makes them durable but also requires specific knowledge to diagnose and repair. The rotor position sensor, stator windings, and control board all interact in ways that generic appliance technicians often misread. Our SmartDrive Washer Repair service is built around the WL and GW platform.

Common Problems We Fix

• Washer not spinning — rotor position sensor fault, error code Err or 37
• Washer not filling — water-inlet valve fault, error code 46 or 48
• Washer stopping mid-cycle with lid-lock fault — error code 58 or 59
• Drum making grinding or rumbling noise — bearing or rotor fault
• Washer not draining — pump blockage or pump motor fault, error code 34
• Excessive vibration during spin — load-sensing or suspension fault

Error Codes We Diagnose

Fisher & Paykel SmartDrive error codes include: 37 (rotor position sensor fault), 34 (drain fault), 46 (hot-water valve fault), 48 (cold-water valve fault), 58 (lid-lock fault), and Err (control board communication error). Our technicians use factory diagnostic mode to run individual component tests and retrieve the fault history stored in the control board.

Models We Service

• WL Series — SmartDrive top-load washers (6 kg – 10 kg)
• GW Series — GWL SmartDrive washers (all capacities)
• AquaSmart Series — Compact SmartDrive models

Our Repair Process

1. Book — Note the error code and the last action the washer completed.
2. Diagnose — Motor, sensor, valve, and board tested using factory tools.
3. Estimate — Repair cost quoted per component fault before work begins.
4. Repair — Genuine WL/GW series parts fitted; full wash cycle run to verify.
5. Warranty — 90-day labour warranty on all SmartDrive repairs.

Transparent Pricing

SmartDrive repairs are straightforward when you know the platform — rotor position sensors and pump motors are common fixes at predictable costs. We quote upfront. Book your SmartDrive repair today.

Fisher & Paykel Dryer Repair — Heat-pump and vented dryer repairs by DH-series trained technicians.

Fisher & Paykel’s DH-series heat-pump dryers are among the most energy-efficient dryers available, but their refrigerant-circuit technology means standard dryer technicians often lack the training to diagnose them accurately. Our Dryer Repair service covers both DH-series heat-pump models and vented dryer variants, with technicians specifically trained on the heat-pump circuit.

Common Problems We Fix

• Dryer not heating — heat-pump compressor fault or heater element failure, error code H or F1
• Dryer taking too long — blocked heat exchanger or moisture-sensor fault, error code F3
• Dryer stopping mid-cycle — thermal cutout or overtemperature fault, error code F4 or F5
• Drum not turning — belt snapped or motor fault
• Dryer displaying error and refusing to start — control board fault, error code Er
• Excessive noise during tumble — drum bearing or blower wheel fault

Error Codes We Diagnose

Fisher & Paykel DH-series dryer error codes include: F1 (heating fault), F3 (moisture sensor fault), F4 (overtemperature), F5 (thermal cutout open), H (high-temperature alarm), and Er (control board error). Our technicians use factory service mode to retrieve the fault log and test the heat-pump circuit pressures before quoting.

Models We Service

• DH Series — Heat-pump condenser dryers (5 kg – 8 kg)
• DE Series — Vented electric dryers
• GDE Series — Legacy vented dryer models

Our Repair Process

1. Book — Note whether the dryer is heat-pump or vented, and any error codes shown.
2. Diagnose — Heat-pump circuit, drum, motor, and sensors all assessed on-site.
3. Estimate — Written quote before any parts are ordered or work begins.
4. Repair — Genuine DH-series parts fitted; full dry cycle run to confirm repair.
5. Warranty — 90-day labour warranty on all dryer repairs.

Transparent Pricing

Heat-pump dryer repairs require specialist knowledge and cost more than simple vented dryer fixes — but they save you the cost of a new appliance. We price all repairs transparently. Book your dryer repair today.

Fisher & Paykel Cooktop Repair — Induction or gas — get your Fisher & Paykel cooktop cooking again.

Fisher & Paykel produces two distinct cooktop technologies — CI-series induction and CG-series gas — and each requires a different diagnostic approach. Our Cooktop Repair service covers both platforms, with technicians equipped to test induction power modules and gas-burner systems with equal confidence.

Common Problems We Fix

• Induction zone not detecting cookware — power module or coil fault, error code E1 or E6
• Cooktop showing error and locking out — error code Er or F
• Gas burner igniting but not holding flame — thermocouple fault
• Igniter clicking continuously after burner is lit
• Touch controls unresponsive or erratic — control panel fault
• Induction cooktop tripping circuit breaker — power-board fault

Error Codes We Diagnose

Fisher & Paykel induction cooktop error codes include: E1 (no pot detected / coil fault), E2 (temperature sensor fault), E6 (IGBT overtemperature), Er (general lockout), and F (fan fault on ventilated models). For gas cooktops, fault indicators relate to ignition failure or gas-valve behaviour rather than digital codes.

Models We Service

• CI Series — Induction cooktops (60 cm, 75 cm, 90 cm)
• CG Series — Gas on glass cooktops
• CGS Series — Gas on stainless cooktops with wok burner
• CPV3 Series — Venting induction cooktop

Our Repair Process

1. Book — Note whether the cooktop is induction or gas when booking.
2. Diagnose — Zone-by-zone or burner-by-burner testing performed on-site.
3. Estimate — Repair cost quoted per fault before work begins.
4. Repair — Genuine F&P parts fitted; gas connections leak-tested after repair.
5. Warranty — 90-day labour warranty on all cooktop repairs.

Transparent Pricing

Cooktop repairs are priced by fault type — induction power-module replacements and gas thermocouple swaps have very different costs, and we quote clearly for each. Book your cooktop repair today.

Fisher & Paykel Wine Refrigeration Repair — Precision temperature control restored for your Fisher & Paykel wine cabinet.

Fisher & Paykel’s RS-series wine cabinets are precision appliances designed to hold stable temperatures between 5 °C and 18 °C — a range far narrower than a standard refrigerator. Temperature drift, vibration, or humidity changes can compromise an entire collection. Our Wine Refrigeration Repair service is designed around the specific demands of the RS-series platform.

Common Problems We Fix

• Cabinet not reaching or holding set temperature — possible compressor or sensor fault
• Temperature fluctuating despite stable ambient conditions — error code T or Sensor
• Compressor running continuously without achieving setpoint
• Excessive condensation inside cabinet — door seal or defrost fault
• Interior light not working or staying on — lid switch or LED board fault
• Display panel unresponsive or showing error code E or H

Error Codes We Diagnose

Fisher & Paykel RS-series wine cabinet error codes include: E1 (evaporator sensor fault), E2 (cabinet temperature sensor fault), H (high-temperature alarm), dF (defrost fault), and Er (control board error). Our technicians access factory diagnostic mode to read the full fault history and identify whether the fault is in the sealed system, sensors, or control electronics.

Models We Service

• RS Series — Single-zone and dual-zone wine cabinets (60 cm & 90 cm)
• RS90 — 90 cm integrated wine column
• RS60 — 60 cm freestanding wine cabinet
• Classic Series — Legacy wine storage units

Our Repair Process

1. Book — Note the cabinet model and any error codes displayed.
2. Diagnose — Sealed system, sensors, and controls tested on-site.
3. Estimate — Repair cost quoted before any parts are ordered.
4. Repair — Genuine RS-series parts fitted; cabinet temperature verified post-repair.
5. Warranty — 90-day labour warranty on all wine cabinet repairs.

Transparent Pricing

Wine cabinet repairs range from simple sensor replacements to compressor or sealed-system work. We quote all fault types clearly before starting. Contact us today to protect your collection.

Fisher & Paykel DishDrawer Repair — Expert DD24 DishDrawer repairs — the specialists other repairers call.

The Fisher & Paykel DishDrawer is unlike any other dishwasher on the market — its drawer-based design uses a unique pump, motor, and latch system that demands specialist knowledge to repair correctly. Our DishDrawer Repair service is built specifically around the DD24 platform, covering single-drawer, double-drawer, and tall-tub variants across every generation.

Common Problems We Fix

• Drawer not draining — error code F1 or U1 (drain fault)
• Drawer not filling with water — error code F2 or U2 (water-inlet fault)
• Drawer not completing cycle — error code F7 or U7 (motor stall)
• Drawer latch not engaging — mechanical latch or lid-switch fault
• Dishes not coming out clean — spray arm blocked or pump pressure low
• Water leaking from base — door-seal or pump-housing fault

Error Codes We Diagnose

Fisher & Paykel DishDrawer error codes include: F1/U1 (drain fault), F2/U2 (fill fault), F3/U3 (water-heating fault), F7/U7 (motor stall), F8/U8 (overfill / flood protection), and F9/U9 (diverter valve fault). Our technicians use factory service mode to retrieve the full fault log and test individual components before quoting.

Models We Service

• DD24 Single DishDrawer — all generations
• DD24 Double DishDrawer — stacked single & double-height
• DD24ST Tall Tub DishDrawer
• DD60 — Legacy double DishDrawer

Our Repair Process

1. Book — Note the error code and which drawer (top or bottom) is faulty.
2. Diagnose — Drawer mechanism, pump, motor, and electronics tested on-site.
3. Estimate — Clear quote before any parts are ordered.
4. Repair — Genuine DD24 parts fitted; full wash cycle run to verify repair.
5. Warranty — 90-day labour warranty on all DishDrawer repairs.

Transparent Pricing

DishDrawer repairs are among the most misquoted jobs in appliance repair — many repairers aren’t familiar with the platform. We’re DishDrawer specialists and price all faults transparently. Book today.

A failing freezer puts expensive frozen food at risk within hours. Our Fisher & Paykel Freezer Repair service prioritises rapid diagnosis and same-visit repair where possible, minimising the thaw risk while restoring your appliance to full operating temperature. We cover all F&P standalone freezer and fridge-freezer combinations.

Common Problems We Fix

• Freezer not reaching -18 °C — possible compressor or refrigerant fault
• Excessive frost build-up blocking the evaporator — error code dF or Ed
• Freezer running continuously but not cold enough
• Door seal torn or misaligned, allowing warm-air ingress
• Defrost heater failed — error code H or temperature alarm
• Evaporator fan motor seized — reduced airflow, uneven freezing

Error Codes We Diagnose

Common Fisher & Paykel freezer error codes include: dF (defrost failure), Ed (evaporator defrost sensor fault), H (high-temperature alarm), F (fan motor fault), and 5 (temperature sensor out of range). Our technicians access factory diagnostic mode to read the full fault log and identify the root cause before any parts are replaced.

Models We Service

• RF Series — ActiveSmart fridge-freezer combinations
• RX Series — French-door models with lower freezer drawer
• E440 and E521 — Freestanding upright freezers
• H Series — Chest freezers

Our Repair Process

1. Book — Call immediately if food is at risk — priority slots available.
2. Diagnose — Sealed-system and electronic diagnosis performed on-site.
3. Estimate — Repair cost quoted before parts are ordered.
4. Repair — Genuine F&P parts fitted; freezer temperature verified post-repair.
5. Warranty — 90-day labour warranty on all freezer repairs.

Transparent Pricing

Freezer repairs range from simple defrost-heater replacements to sealed-system recharges — each priced transparently before we start. Contact us now if your freezer temperature is rising.

Fisher & Paykel Range Repair — Restore your Fisher & Paykel range to full cooking performance.

Fisher & Paykel’s OR-series freestanding ranges combine a gas or dual-fuel cooktop with a full-size oven cavity, meaning a single fault can take out your entire cooking setup. Our Range Repair service covers both the cooktop burner assembly and the oven section in one visit, getting your kitchen fully operational again as quickly as possible.

Common Problems We Fix

• Burner igniter clicking but not lighting — error or fault code F1
• Oven not reaching temperature or heating unevenly
• Oven fan motor seized or noisy during bake cycles
• Gas safety valve not opening — flame won’t hold after lighting
• Oven door hinge worn, door not sealing — heat loss and temperature error
• Control knob or electronic control panel unresponsive — error code E or Er

Error Codes We Diagnose

Fisher & Paykel range error codes include: F1 (control board fault), F3 (oven temperature sensor open), F4 (oven temperature sensor shorted), E (electrical fault), and Er (general error requiring reset). We use factory diagnostic mode to read the full fault history and confirm the root cause before ordering parts.

Models We Service

• OR Series — Freestanding gas and dual-fuel ranges (60 cm & 90 cm)
• Classic Series — Legacy freestanding range models
• RGV2 Series — Gas range with variable simmer burners

Our Repair Process

1. Book — Mention gas smell or safety concern for priority dispatch.
2. Diagnose — Gas pressure, ignition, and oven systems all checked.
3. Estimate — Written quote covering all faults found.
4. Repair — Genuine F&P parts fitted; gas connections leak-tested after repair.
5. Warranty — 90-day labour warranty on all range repairs.

Transparent Pricing

Range repairs are quoted per fault, so you only pay for what’s actually wrong. Gas-related repairs require licensed gas-fitting work — included in our service. Book your range repair today.

Fisher & Paykel’s OB-series built-in ovens include pyrolytic self-cleaning models, combi-steam ovens, and fan-forced convection units. Each has its own unique service requirements. Our Oven Repair service covers the full OB range, with technicians specifically trained on pyrolytic door-lock systems and combi-steam generators — not just general oven electrics.

Common Problems We Fix

• Oven not heating — bake or grill element failed, error code F3 or F4
• Pyrolytic cycle locked but won’t start — door-lock mechanism fault
• Oven temperature inaccurate — temperature sensor drift, error code F2
• Steam generator not filling or producing steam — combi-steam models
• Fan motor seized — uneven cooking in fan-forced mode
• Touchpad or control board unresponsive — error code E or Er

Error Codes We Diagnose

Fisher & Paykel OB-series oven error codes include: F1 (control board fault), F2 (temperature sensor short), F3 (temperature sensor open), F4 (oven overheated), F5 (door-lock fault), and Er (general electronic error). We access factory diagnostic mode to confirm which component has failed before ordering parts.

Models We Service

• OB60 Series — 60 cm built-in pyrolytic ovens
• OB60SC — Combi-steam oven
• OB76 Series — 76 cm wide built-in ovens
• OB90 Series — 90 cm built-in ovens
• Classic Series — Legacy built-in oven models

Our Repair Process

1. Book — Note any error codes and whether the fault involves pyrolytic or steam functions.
2. Diagnose — Element, sensor, lock, and board all tested systematically.
3. Estimate — Itemised repair quote before any work begins.
4. Repair — Genuine OB-series parts fitted and oven tested through a full cycle.
5. Warranty — 90-day labour warranty on all oven repairs.

Transparent Pricing

Oven repair costs depend on whether the fault is electronic, mechanical, or element-related. We quote clearly for each fault type. Book your Fisher & Paykel oven repair today.

Fisher & Paykel Multi-Appliance Service — Service multiple Fisher & Paykel appliances in one visit and save.

If more than one Fisher & Paykel appliance in your home needs attention, there’s no reason to pay two call-out fees. Our Multi-Appliance Service sends a technician equipped to assess and repair several units in a single visit — saving you time and money while getting your whole kitchen and laundry back up to scratch.

Common Problems We Fix

• Refrigerator temperature fault alongside a washer drain issue
• Oven and cooktop faults addressed together in one kitchen visit
• DishDrawer and range serviced at the same appointment
• Annual maintenance across fridge, dishwasher, and dryer in one call
• Wine cabinet and refrigerator compressor checks combined

What’s Included

A single call-out fee covers all appliances listed at booking. Each appliance receives its own diagnostic assessment, fault report, and repair quote. Parts for all units are sourced from our authorised F&P supply chain. You receive a combined service docket at the end of the visit with individual warranty periods for each appliance repaired.

Models We Service

• ActiveSmart Refrigerators & Freezers — RF & RX series
• DishDrawer Dishwashers — DD24 series
• SmartDrive Washers — WL & GW series
• Pyrolytic & Combi-Steam Ovens — OB series
• Induction & Gas Cooktops — CI & CG series
• Gas Ranges — OR series
• Heat-Pump Dryers — DH series
• Wine Cabinets — RS series

Our Repair Process

1. Book — List all appliances requiring attention when you book.
2. Diagnose — Each appliance inspected and faults identified individually.
3. Estimate — Combined or itemised quote provided before any repairs begin.
4. Repair — All approved repairs completed in the same visit.
5. Warranty — 90-day labour warranty applies to each repaired appliance.

Transparent Pricing

One call-out fee. Multiple appliances fixed. Ask about our multi-appliance discount when booking two or more units on the same visit. Contact us today to arrange your combined service call.

Fisher & Paykel Refrigerator Repair — Keep your ActiveSmart refrigerator running at peak efficiency.

Fisher & Paykel’s ActiveSmart refrigerators use adaptive technology to manage temperature and airflow — which means faults can be subtle and difficult to diagnose without the right tools. Our Refrigerator Repair service covers every RF and RX series model, from single-door top-freezers to large French-door configurations.

Common Problems We Fix

• Not cooling or reaching set temperature — often fault code F or dF
• Excessive frost build-up on evaporator coils — error code 5 or Ed
• Compressor running but fridge warm — possible sealed-system fault
• Water pooling inside the fridge — blocked defrost drain
• Ice maker not producing ice on RF series models
• Display panel unresponsive or showing error code E or H

Error Codes We Diagnose

Common Fisher & Paykel refrigerator error codes include: F (fan fault), dF (defrost fault), 5 (sensor fault), Ed (evaporator defrost sensor), E (electrical fault), and H (high-temperature alarm). Our technicians use factory diagnostic mode to read the full fault history and pinpoint the root cause.

Models We Service

• RF Series — ActiveSmart top-freezer and bottom-freezer
• RX Series — French-door and quad-door configurations
• RS Series — Integrated column refrigerators
• E Series — Classic freestanding models

Our Repair Process

1. Book — Note any error codes displayed when booking.
2. Diagnose — Full refrigerant-circuit and electronic diagnosis on-site.
3. Estimate — Written quote before any parts are ordered.
4. Repair — Genuine F&P parts fitted and cooling performance verified.
5. Warranty — 90-day labour warranty on all refrigerator repairs.

Transparent Pricing

Refrigerator repair costs vary by fault type. Sealed-system repairs cost more than electronic or mechanical fixes, and we’ll quote clearly before proceeding. Contact us to book your refrigerator repair today.